|
|
We carry a full line of Poly Tek products.
If you do not see what you are looking for here give us a call for details and prices. |
Platinum Base Rubber
PlatSil Gel-10
Platil Gel-10, a translucent, soft rubber, is an excellent mold material for delicate casting projects and creating special effects. Gel-10 is a two-part, addition cure, liquid silicone system with an easy 1:1 mix ration. After mixing Parts A and B, Gel-10 cures within 30 minutes at room temperature to a soft, tough rubber. Gel-10 does not shrink on curing. |
|
FEATURES |
- Soft (~A10), translucent, silicone rubber
- Easy 1:1 mix ratio
- PlatSil 71R Retarder slows the cure
- Bonds to Poly Plastics
|
- Fast 30-minute demold with 6-minute work time
- PlatSil 71/73X Accelerator speeds the cure
- PlatThix thickens the mix to a brushable paste
|
|
|
 |
Knead-a-Mold
Knead-a-Mold is a two-part platinum-cured silicone mold-making system that is safe and easy to use. It works beautifully with resins, low-temperature melt alloys, paper and air-dry clays, polymer clay, wood putty, chocolate and more!
Excellent for replicating vertical, small or hard-to-reach areas. Non-toxic and food-safe, Knead-a-Mold can be baked at up to 300°F constant temperature or 600°F intermittently. No special equipment, tools or release agents are needed.
Purfect for sculpture, restoration, jewelry, crafts " hobbies, taxidermy, candy, chocolate, soap, candles... and more!
FEATURES
- Non-Toxic
- Food-Safe
- No Clean Up
- Captures The Finest Details
- Can Be Heated
- Very Quick Cure Time
|
Brush-a-Mold
Brush-a-Mold is a brush-on, two-part silicone mold making system. It is easy to use, replicates the finest details, is safe, non-toxic, and requires no release agents. It is perfect for covering large surfaces, life-casting and in-situ mold making. Brush-a-Mold has a pot life/gel time of 16 minutes and a cure time of 20-30 minutes at ambient temperature (70-72°F).
Perfect for... covering large surfaces, sculpture, life-casting, in-situ mold making, crafts & hobbies, restoration, taxidermy... The Possibilities are endless! |
 |
 |
FEATURES
- Non-Toxic
- Fast
- No Clean Up
- Captures The Finest Details
|
PlatSil
71 Series Silicone Rubber
PlatSil 71 Series mold rubbers are two-component, addition-cure, platinum catalyzed,
high tear strength, flexible mold compounds. They have tough knotty
tear strength which make them especially valuable to the mold making
industry. They are recommended as mold material for polyester, epoxy,
polyurethane resins, waxes and many other materials. PlatSil silicones
are preferred because on curing, they do not shrink, they do not produce
alcohol like tin-catalyzed silicones which can inhibit urethane castings,
and they can be heat accelerated to speed the cure. |
71-10 |
| |
|
71-11 |
| |
|
71-20 |
| |
|
PlatThix - Thickener |
| 71-10 Demold Time: 30 minutes |
| Mix Ratio: 10A to 100B |
Shore A Hardness: 10 |
Pour Time: 5 min |
| Color: Pink |
Viscosity: 3,500 cP |
26 in3 / lb |
| 71-11 Demold Time: 4 hours |
| Mix Ratio: 1A to 1B |
Shore A Hardness: 11 |
Pour Time: 15 min |
| Color: Blue |
Viscosity: 15,000 cP |
24.7 in3 / lb |
| 71-20 Demold Time: 4 hours |
| Mix Ratio: 1A to 1B |
Shore A Hardness: 20 |
Pour Time: 25 min |
| Color: Light Purple |
Viscosity: 26,000 cP |
24.7 in3 / lb |
71-30, 71-40, 73-45 and other products are available.
Please call the store for details. |
4
oz |
$9.00 |
|
| 1
lb |
$16.00 |
|
|
PlatSil 71 & 73X Accelerator |
| 4
oz |
$28.00 |
|
| 1
lb |
$84.00 |
|
|
PlatSil 71 & 73R Retarder |
| 4
oz |
$8.75 |
|
| 1
lb |
$22.00 |
|
Polyurethane Rubber
Poly-Fast
72-40
Poly-Fast 72-40 may be poured or thickened and applied by trowel or
brush, to make high quality, flexible molds. These molds are especially
useful for making wax or plaster casts and with release agents or barrier
coats are good for casting resins and concrete. |
72-40 |
|
|
|
Part 72D Thickener (w/extra
part A) |
|
|
| 72-40 |
Mix Ratio: 10A
to 100B
Color: Ivory |
Shore A Hardness:
40
Viscosity: 4,400 cP |
Pour Time: 30 min
20 in3 / lb |
|
Poly 74 Series
Urethane Rubber
The 74 series liquid rubbers make durable, easy releasing molds for
casting gypsum plasters and waxes without release agents, but are
also excellent for casting cement and resins of epoxy, polyester,
urethane and acrylic with proper release agents. |
74-20 |
|
|
|
74-29 |
|
|
|
74-30 |
| 74-20 |
Mix Ratio: 1A to 2B
Color: Yellow |
Shore A Hardness: 20
Viscosity: 800 cP |
Pour Time: 30 min
27.5 in3 / lb |
| 74-29 |
Mix Ratio: 1A to 1B
Color: Black or White |
Shore A Hardness: 30
Viscosity: 2,800 cP |
Pour Time: 30 min
27.5 in3 / lb |
| 74-30 |
Mix Ratio: 1A to 1B
Color: Amber or Clear |
Shore A Hardness: 30
Viscosity: 2,000 cP |
Pour Time: 30 min
27.5 in3 / lb |
| 74-45 |
Mix Ratio: 1A to 1B
Color: Yellow |
Shore A Hardness: 45
Viscosity: 2,500 cP |
Pour Time: 30 min
27.5 in3 / lb |
|
| |
|
74-45 |
|
|
|
|
Part C Softener for 74 & 75 |
|
|
|
74 / 75 X Accelerator |
|
|
| Polygel Self Thickening
Rubber for Brushed or Sprayed Molds
|
Polygel 35, 40, 50 - Paste |
|
|
| |
|
Polygel 35, 50 - Spray |
|
|
| |
| 4 lbs |
$55.00 |
| 16 lbs |
$123.00 |
| 80 lbs |
$499.00 |
| 900 lbs |
$4,550.00 |
Patented Polygel® mold rubbers are 1:1 mix liquids that thicken during
mixing to a brush able or spray able viscosity. No Cab-O-Sil® or Part
D is needed. Polygel® 50 can be applied about 1/4 inch thick while
Polygel® 40 is thinner for best detail penetration. Polygel® Spray
50 is a spray able version.
Polygel® Spray 50 is a spray able version of Polygel® 50. Polygel®
50 Spray is softer for more delicate and undercut models and castings. A
mold can be sprayed in one application and cured overnight. Spraying
is a very economical alternative to brushing for molds made over large
models and surface areas.
Polygel 35: Mix Ratio: 1A to 1B, Shore A Hardness: 35, Color: Blue
Polygel 40: Mix Ratio: 1A to 1B, Shore A Hardness: 40, Color: Ivory
Polygel 50: Mix Ratio: 1A to 1B, Shore A Hardness: 50, Color: Ivory |
Silicone Rubber
TinSil 70
Series Silicone Rubber
All TinSil 70 Series mold rubbers are tin-catalyzed, condensation-cure
systems. They are ideal for molds where easy release or high temperature
resistance is needed. They are recommended for evaluation as mold
materials for polyester, epoxy, and polyurethane resins and waxes.
All Tinsil rubbers have a demold time of sixteen hours. |
70-11 |
| |
|
70-25 |
| |
|
70-30 |
| 70-11 Soft, durable silicone with high tear strength. |
| Mix Ratio: 10A to 100B |
Shore A Hardness: 11 |
Pour Time: 60 min |
| Color: Green |
Viscosity: 12,000 cP |
25.3 in3 / lb |
| 70-25 |
| Mix Ratio: 10A to 100B |
Shore A Hardness: 25 |
Pour Time: 60 min |
| Color: Blue |
Viscosity: 15,000 cP |
25.3 in3 / lb |
| 70-30 |
| Mix Ratio: 2A to 100B |
Shore A Hardness: 30 |
Pour Time: 60 min |
| Color: Beige |
Viscosity: 26,000 cP |
25.3 in3 / lb |
| 70-31 |
| Mix Ratio: 10A to 100B |
Shore A Hardness: 25 |
Pour Time: 60 min |
| Color: |
Viscosity: 15,000 cP |
25.3 in3 / lb |
|
| |
|
70-31 |
| |
|
TinThix - Thickener |
| 4 oz |
$10.00 |
|
| 1 lb |
$17.00 |
|
|
TinSil FastCat - Accelerator |
| 4 oz |
$14.00 |
|
| 1 lb |
$36.00 |
|
Silicone
Fluid 50 cSt
For thinning Platsil and TinSil silicone rubbers. Low viscosity 50
cSt Silicone Fluid can be sparingly added to the mixed rubber to thin
the mix with some loss of strength and hardness. |
|
| 2
lbs |
$20.00 |
|
| 8
lbs |
$63.00 |
|
| |
Plas-Pak Systems
Spray Poly Plastics, Polygel® Rubbers &
TinSil® Spray 25
The Plas-Pak systems are relatively inexpensive and surprisingly versatile when used with Polytek liquid rubbers and plastics. They can be used to spray a variety of rubbers and plastics or they can just be used to mix and dispense without spraying. Interested in spraying silicone? We can do that too! Call for more information.
10:1 mix ratio. Designed to thicken almost instantly upon mixing. Tinsil Spray 25 is available in pre-packaged cartridges ready for use with the Plas-Pak sprayer or it can be supplied in bulk. |
| Sprayer |
$599.00 |
|
| Cartridges |
$7.00 |
|
| Static mixers |
$3.00 |
|
Tinsil Spray 25
44 lbs |
$448.00 |
|
PolyBond
A polyurethane adhesive that is great for repairing torn molds. PolyBond has a 1A:3B mix ration (by weight), a 3 minute working time and a 15 minute cure time. |
|
| 2 lb kit |
$42.00 |
|
| |
Latex
Poly Latex False Face
Poly Latex False Face Compound is a one part pourable liquid that, when poured into
a dry, unsealed gypsum mold, cures to a high-strength, flexible casting rubber. False
Face was formulated to produce flexible hollow parts for uses such as novelty masks,
flexible sculpture, and animatronic applications. |
| |
Poly Latex
60
Poly Latex 60 is a one part, brush-on liquid which after multiple
coats is built up to form a tough rubber blanket mold, often used
for casting plaster, concrete and limited casting with some resins. |
| |
|
|
|
